I frequently transport a small electric lawnmower in my car boot - the handle comes off so it's relatively easy to carry and fits in easily. What's a right pain though is that the cable is permanently attached to both the handle and the mower which makes it really awkward to lift in and out.
Can I cut the wire and fit an in-line connector? For example https://cpc.farnell.com/permaplug/nc10- ... connectors
The mower is double insulated, not used in the rain, and when assembled there is no strain on the cable.
Got a credit card? use our Credit Card & Finance Calculators
Thanks to Wasron,jfgw,Rhyd6,eyeball08,Wondergirly, for Donating to support the site
In-line electrical connector
-
- Lemon Slice
- Posts: 479
- Joined: November 4th, 2016, 1:56 pm
- Has thanked: 1308 times
- Been thanked: 108 times
-
- Lemon Quarter
- Posts: 1589
- Joined: November 4th, 2016, 3:54 pm
- Has thanked: 33 times
- Been thanked: 477 times
Re: In-line electrical connector
The short answer is yes you can. All the electric mowers I've seen have 2 core cable. There are loads of connectors for sale on eBay or Amazon that will also do the job for you. Just make sure you DON'T wire the connector with the male pins to the lead that plugs into the power supply
-
- Lemon Half
- Posts: 9129
- Joined: November 4th, 2016, 1:16 pm
- Has thanked: 4140 times
- Been thanked: 10032 times
Re: In-line electrical connector
MyNameIsUrl wrote:
Can I cut the wire and fit an in-line connector? For example https://cpc.farnell.com/permaplug/nc10- ... connectors
The mower is double insulated, not used in the rain, and when assembled there is no strain on the cable.
The only thing I'd be worried about regarding your linked connector is that there's nothing in the way of a mechanical connection between the two halves, and I'd be concerned that they could work apart during operation of the mower.
That would be a show-stopper for me personally, and I'd be looking at some sort of screw-fit connector that will carry out the same function, but with a mechanical screw-connection holding the two connector-halves together, so something like this -
Knightsbridge JB0011 Weatherproof IP68 (@2bar) Plug and Socket Inline Cable Connector, 3-Pole, rated to 16 A -
Source, and link to the above product - https://www.amazon.co.uk/Knightsbridge-Socket-Cable-Connector-3-Pole/dp/B076QH9VF4
There may be better screwed alternatives to the above, so this is just an example of what I'd personally be looking for, rather than just a 'squeeze-fit' connector...
Cheers,
Itsallaguess
-
- Lemon Slice
- Posts: 479
- Joined: November 4th, 2016, 1:56 pm
- Has thanked: 1308 times
- Been thanked: 108 times
Re: In-line electrical connector
richlist wrote:Just make sure you DON'T wire the connector with the male pins to the lead that plugs into the power supply
Thanks, yes, point taken.
-
- Lemon Slice
- Posts: 621
- Joined: November 4th, 2016, 3:46 pm
- Has thanked: 608 times
- Been thanked: 368 times
Re: In-line electrical connector
Itsallaguess wrote:MyNameIsUrl wrote:
Can I cut the wire and fit an in-line connector? For example https://cpc.farnell.com/permaplug/nc10- ... connectors
The mower is double insulated, not used in the rain, and when assembled there is no strain on the cable.
The only thing I'd be worried about regarding your linked connector is that there's nothing in the way of a mechanical connection between the two halves, and I'd be concerned that they could work apart during operation of the mower.
That would be a show-stopper for me personally, and I'd be looking at some sort of screw-fit connector that will carry out the same function, but with a mechanical screw-connection holding the two connector-halves together, so something like this -
Knightsbridge JB0011 Weatherproof IP68 (@2bar) Plug and Socket Inline Cable Connector, 3-Pole, rated to 16 A -
Source, and link to the above product - https://www.amazon.co.uk/Knightsbridge-Socket-Cable-Connector-3-Pole/dp/B076QH9VF4
There may be better screwed alternatives to the above, so this is just an example of what I'd personally be looking for, rather than just a 'squeeze-fit' connector...
Cheers,
Itsallaguess
The other perspective on this is that if the supply flex inadvertently snags somewhere then any resulting tug will separate the in-line plug and socket and these can then then be re-connected once the snagging has been resolved. The screw type connector you suggest will lead to strain on the flex connections which might, over time, result in a safety issue. As well as cheapness, I suspect this is one reason why every piece of mains powered garden equipment I have ever bought (lawn mower, hedge trimmer, strimmer, etc) has always had a pull-apart in-line plug and socket supplied as standard. There is probably a CE standard covering these things.
Who is online
Users browsing this forum: No registered users and 33 guests