Got a credit card? use our Credit Card & Finance Calculators
Thanks to Anonymous,bruncher,niord,gvonge,Shelford, for Donating to support the site
Cabinet Hinges
-
- Lemon Slice
- Posts: 834
- Joined: November 4th, 2016, 6:29 pm
- Has thanked: 153 times
- Been thanked: 209 times
Cabinet Hinges
I've just had a kitchen cabinet door hinge break. The hinge is about 30 years old and labelled Salice 2A7. Where can I get a replacement hinge? Ideally one that simply slots in to the existing hole.
Are these things pretty standard? There's a used Salice 2A7 on ebay (though it looks slightly different to mine) or would I be better off buying a newer version?
Thanks
Are these things pretty standard? There's a used Salice 2A7 on ebay (though it looks slightly different to mine) or would I be better off buying a newer version?
Thanks
-
- Lemon Half
- Posts: 8089
- Joined: November 4th, 2016, 11:24 am
- Has thanked: 7 times
- Been thanked: 3129 times
Re: Cabinet Hinges
Direct form the supplier? https://salicedirect.com/products/salice-45-short-arm-positive-angle-hinge-c2abv99
"Compatible with all snap-on or screw-on mount plates This hinge may be stamped with either 2A7 or 2AV."
"Compatible with all snap-on or screw-on mount plates This hinge may be stamped with either 2A7 or 2AV."
-
- Lemon Slice
- Posts: 834
- Joined: November 4th, 2016, 6:29 pm
- Has thanked: 153 times
- Been thanked: 209 times
Re: Cabinet Hinges
mc2fool wrote:Direct form the supplier? https://salicedirect.com/products/salice-45-short-arm-positive-angle-hinge-c2abv99
"Compatible with all snap-on or screw-on mount plates This hinge may be stamped with either 2A7 or 2AV."
Thanks, though I'm still not entirely sure that that's the correct one. How do I know if mine has a short arm? Or a positive 45 degree angle (whatever that is!)? It has however made me realise that the 2A7 one on ebay is not necessarily of the same vintage as mine, so may not be compatible.
I'll try sending a photo of what I've got to Salice, to see what that say.
-
- Lemon Quarter
- Posts: 2595
- Joined: November 4th, 2016, 3:36 pm
- Has thanked: 1120 times
- Been thanked: 1182 times
Re: Cabinet Hinges
mc2fool wrote:Direct form the supplier? https://salicedirect.com/products/salice-45-short-arm-positive-angle-hinge-c2abv99
"Compatible with all snap-on or screw-on mount plates This hinge may be stamped with either 2A7 or 2AV."
That particular one is a 45° one for a corner cabinet — this type of thing, https://mhcustom.com/kitchen-corner-cabinet-storage-solutions/.
Most kitchen cabinet hinges are of this general type: https://www.screwfix.com/p/blum-steel-sprung-concealed-hinges-110mm-2-pack/14286. They are full overlay (the door {almost} covers the edges of the sides of the carcase when it is closed) and open a little more than 90°. Ones that open further may be used for 90° corner cabinets to allow better access. Using a different brand is not normally a problem (although I would not mix brands on the same door, just in case they hinge differently). You would need to change the backplate if you change the brand but it is just two screws each.
The screw holes in the backplates are a standard distance apart, and the 35mm hole in the door is standard. The screw hole positions in the door can vary but this isn't normally a problem. A bit of soap (dry, from a bar) or candle wax, crayon or whatever helps the screw go into the MDF door.
The backplate fixings can be one of three types:
Normal wood screws;
M6 screws that need a 5mm pre-drilled hole, https://www.screwfix.com/p/zinc-plated-hinge-screws-m6-x-16mm-100-pack/89259;
Screws with plastic dowels, https://www.debonairjoineryproducts.co.uk/product/blum-hinge-knock-in-plastic-expansion-dowels-8-or-10-mm-with-screws/.
The M6 screws do not fit backplates designed for the other types (or are very tight).
Julian F. G. W.
-
- Lemon Slice
- Posts: 834
- Joined: November 4th, 2016, 6:29 pm
- Has thanked: 153 times
- Been thanked: 209 times
Re: Cabinet Hinges
jfgw wrote:mc2fool wrote:Direct form the supplier? https://salicedirect.com/products/salice-45-short-arm-positive-angle-hinge-c2abv99
"Compatible with all snap-on or screw-on mount plates This hinge may be stamped with either 2A7 or 2AV."
That particular one is a 45° one for a corner cabinet — this type of thing, https://mhcustom.com/kitchen-corner-cabinet-storage-solutions/.
Most kitchen cabinet hinges are of this general type: https://www.screwfix.com/p/blum-steel-sprung-concealed-hinges-110mm-2-pack/14286. They are full overlay (the door {almost} covers the edges of the sides of the carcase when it is closed) and open a little more than 90°. Ones that open further may be used for 90° corner cabinets to allow better access. Using a different brand is not normally a problem (although I would not mix brands on the same door, just in case they hinge differently). You would need to change the backplate if you change the brand but it is just two screws each.
The screw holes in the backplates are a standard distance apart, and the 35mm hole in the door is standard. The screw hole positions in the door can vary but this isn't normally a problem. A bit of soap (dry, from a bar) or candle wax, crayon or whatever helps the screw go into the MDF door.
The backplate fixings can be one of three types:
Normal wood screws;
M6 screws that need a 5mm pre-drilled hole, https://www.screwfix.com/p/zinc-plated-hinge-screws-m6-x-16mm-100-pack/89259;
Screws with plastic dowels, https://www.debonairjoineryproducts.co.uk/product/blum-hinge-knock-in-plastic-expansion-dowels-8-or-10-mm-with-screws/.
The M6 screws do not fit backplates designed for the other types (or are very tight).
Thanks so much for that explanation Julian, it's a bit clearer now. My existing backplate appears to use M6 screws, so I'm hoping that if I choose the same make I may be able to retain the existing backplate. There seems to be a vast number of different hinges though, but hopefully Salice will be able to advise on the correct sort if I send them some pics.
-
- Lemon Slice
- Posts: 397
- Joined: November 4th, 2016, 6:45 pm
- Has thanked: 78 times
- Been thanked: 278 times
Re: Cabinet Hinges
Stompa wrote:I've just had a kitchen cabinet door hinge break. The hinge is about 30 years old and labelled Salice 2A7. Where can I get a replacement hinge? Ideally one that simply slots in to the existing hole.
Are these things pretty standard? There's a used Salice 2A7 on ebay (though it looks slightly different to mine) or would I be better off buying a newer version?
Thanks
Screwfix do a range of different sized hinges. They also do a hinge repair plate which is really useful if the wood where the hinge fixes into is damaged, which inevitably happens with old doors.
-
- Posts: 1
- Joined: December 23rd, 2023, 6:40 pm
Re: Cabinet Hinges
Cabinet hinges may seem like small details, but they play a crucial role in functionality and aesthetics. Choosing durable, well-designed hinges ensures smooth operation and adds a touch of craftsmanship to your cabinets.
-
- Lemon Quarter
- Posts: 4880
- Joined: November 4th, 2016, 2:24 pm
- Has thanked: 4911 times
- Been thanked: 2147 times
Re: Cabinet Hinges
Hi, welcome to The Lemon Fool. Just out of curiosity, how did you discover TLF? Chrissteven11 wrote:Cabinet hinges may seem like small details, but they play a crucial role in functionality and aesthetics. Choosing durable, well-designed hinges ensures smooth operation and adds a touch of craftsmanship to your cabinets.
-
- Lemon Slice
- Posts: 448
- Joined: November 9th, 2016, 6:14 pm
- Has thanked: 429 times
- Been thanked: 149 times
Re: Cabinet Hinges
CliffEdge wrote:If you need to repair holes you can glue dowels in.
Good idea. A trick I learnt from the days of TMF was to use saw dust with decorators PVA.
john
-
- Lemon Quarter
- Posts: 3920
- Joined: November 6th, 2016, 10:25 pm
- Has thanked: 1247 times
- Been thanked: 2054 times
Re: Cabinet Hinges
csearle wrote:Hi, welcome to The Lemon Fool. Just out of curiosity, how did you discover TLF? Chrissteven11 wrote:Cabinet hinges may seem like small details, but they play a crucial role in functionality and aesthetics. Choosing durable, well-designed hinges ensures smooth operation and adds a touch of craftsmanship to your cabinets.
Are you questioning their unnatural use of intelligent language?
-
- Lemon Quarter
- Posts: 4880
- Joined: November 4th, 2016, 2:24 pm
- Has thanked: 4911 times
- Been thanked: 2147 times
Re: Cabinet Hinges
Exactly.DrFfybes wrote:csearle wrote:Hi, welcome to The Lemon Fool. Just out of curiosity, how did you discover TLF? Chris
Are you questioning their unnatural use of intelligent language?
C.
PS You've passed the Turing test Paul
Who is online
Users browsing this forum: No registered users and 7 guests