I have a power shower which has the 12v pump built into the mixer unit within the shower enclosure. It's not used very often but recently the motor continues running after it's switched off.
With the cover off I can see two microswitches (for 'normal' and 'boost') and one of the little levers appears to stay down intermittently. I'm not sure if the return spring - to push the lever back up when switched off - is part of the lever or part of the switch bit that goes in and out. Before I blast it all with WD40 I though it wise to ask if anyone has a better suggestion. Contact cleaner? Silicone lubricant?
Got a credit card? use our Credit Card & Finance Calculators
Thanks to Anonymous,bruncher,niord,gvonge,Shelford, for Donating to support the site
Sticking microswitch
-
- Lemon Slice
- Posts: 484
- Joined: November 4th, 2016, 1:56 pm
- Has thanked: 1313 times
- Been thanked: 108 times
-
- 2 Lemon pips
- Posts: 155
- Joined: July 19th, 2018, 10:24 am
- Has thanked: 159 times
- Been thanked: 88 times
Re: Sticking microswitch
A regular microswitch has the spring as part of the electical switch, and it can't be serviced or repaired as the microswitch is a sealed unit. If you can get the microswitch out, you will be able to find a replacement for it with a bit of searching.
Re: Sticking microswitch
I had this problem with our Aqualisa Aquastream power shower. On examination I could see that the thermostatic cartridge in the main control had started to leak & drip onto the microswitch which is located directly under the cartridge (poor design). Ended up replacing the thermostatic cartridge (£100) and new loom with microswitch (£40) but they were straight forward to fit myself.
We are are in a hard water area so I reckon think this will be an ongoing problem every 5yrs or so. Not impressed for what was an expensive shower, the previous cheapo Showerforce 2000 lasted 20yrs before it started playing up. but sadly no spares were available by then.
We are are in a hard water area so I reckon think this will be an ongoing problem every 5yrs or so. Not impressed for what was an expensive shower, the previous cheapo Showerforce 2000 lasted 20yrs before it started playing up. but sadly no spares were available by then.
-
- Lemon Half
- Posts: 8548
- Joined: November 8th, 2016, 5:56 am
- Has thanked: 4540 times
- Been thanked: 3669 times
Re: Sticking microswitch
MyNameIsUrl wrote:I have a power shower which has the 12v pump built into the mixer unit within the shower enclosure. It's not used very often but recently the motor continues running after it's switched off.
With the cover off I can see two microswitches (for 'normal' and 'boost') and one of the little levers appears to stay down intermittently. I'm not sure if the return spring - to push the lever back up when switched off - is part of the lever or part of the switch bit that goes in and out. Before I blast it all with WD40 I though it wise to ask if anyone has a better suggestion. Contact cleaner? Silicone lubricant?
My go to for this stuff is Deoxit D5 (but any contact clear will probably help - espeicially if it has lube)
WD40 tends to gunk things in the long term and Silicone is a bit too much on an insulator for my liking where switches are concerned
-
- Lemon Quarter
- Posts: 2591
- Joined: November 4th, 2016, 3:36 pm
- Has thanked: 1120 times
- Been thanked: 1181 times
Re: Sticking microswitch
WD40 dries to leave a sticky residue. Silicone should not be used near switches or commutators as any arcing decomposes it (even the vapours) to form silicon carbide - both an insulator and an abrasive.
Most likely, the only fix is to replace the switch.
Julian F. G. W.
Most likely, the only fix is to replace the switch.
Julian F. G. W.
-
- Lemon Slice
- Posts: 949
- Joined: November 4th, 2016, 11:33 am
- Has thanked: 32 times
- Been thanked: 464 times
Re: Sticking microswitch
Your average microswitch is a rivetted or welded closed unit.
If a microswitch does not click or no longer has a snap option, then it's a mechanical issue. Buy a new one, or buy the replaceable unit containing a new one.
If a microswitch does not click or no longer has a snap option, then it's a mechanical issue. Buy a new one, or buy the replaceable unit containing a new one.
-
- Lemon Slice
- Posts: 446
- Joined: September 1st, 2018, 10:21 pm
- Has thanked: 256 times
- Been thanked: 136 times
Re: Sticking microswitch
A replacement switch will probably cost £2~3. A small price to pay for fixing something.
-
- Lemon Half
- Posts: 7335
- Joined: November 24th, 2016, 3:29 am
- Has thanked: 1703 times
- Been thanked: 3913 times
Re: Sticking microswitch
jaizan wrote:A replacement switch will probably cost £2~3. A small price to pay for fixing something.
Identifying the exact switch is the hard part.
I'm guessing this shower is a Mira "Event" power shower. If correct, Mira will probably want to supply a complete on/off/speed control valve and switch assembly. But for a lot more than £2-3!
-
- Lemon Slice
- Posts: 484
- Joined: November 4th, 2016, 1:56 pm
- Has thanked: 1313 times
- Been thanked: 108 times
Re: Sticking microswitch
Mike4 wrote:jaizan wrote:A replacement switch will probably cost £2~3. A small price to pay for fixing something.
Identifying the exact switch is the hard part.
I'm guessing this shower is a Mira "Event" power shower. If correct, Mira will probably want to supply a complete on/off/speed control valve and switch assembly. But for a lot more than £2-3!
It's actually an Aqualisa power shower. The microswitch is a sort of double siamese type of thing (as there is a boost setting on the pump) which makes it harder to identify a replacement microswitch. Aqualisa supply a new 'loom' which has the two switches in a plastic mount for around £65. Thanks to jaizan's estimate I now have a better idea of just how much the Aqualisa mark-up is!
Who is online
Users browsing this forum: No registered users and 3 guests